|
Feature Summary CC3-CAJUN
|
|
Form Factor
|
CompactPCI Single size CompactPCI style Eurocard (160x100mm2),
front panel width 4HP (20.3mm)
|
|
Processor
|
Designed for Intel® ULV Celeron® and
LV Pentium® III Micro FC-BGA processors (Tualatin 0.13µ generation),
maximum junction temperature 100°C, processor thermal design power classification:
- CC3-1: 400MHz ULV Celeron, 0.95V, 100MHz FSB, 256KB L2 cache, 3.4W typical
- CC3-2: 650MHz ULV Celeron, 1.10V, 100MHz FSB, 256KB L2 cache, 7.0W typical
- CC3-3: 800MHz LV Pentium 3, 1.15V, 133MHz FSB, 512KB L2 cache, 11.2W typical
- CC3-4: 933MHz LV Pentium 3, 1.15V, 133MHz FSB, 512KB L2 cache, 12.2W typical
|
|
Chipset
|
Intel i815G chip set consisting of:
- 82815 Graphics/Memory Controller Hub (GMCH)
- 82801 I/O Controller Hub (ICH2)
- 82802 Firmware Hub (FWH)
- 8761 LPC Super I/O
|
|
Memory
|
- 144-pin SO-DIMM socket
- Support for up to 512MB, PC133, non ECC, unbuffered SDRAM
- Support for serial presence detect (SPD) SO-DIMMs
|
|
Video
|
-
Both analog monitor and digital flat-panel display support by DVI-I connector (front panel),
up to 1280x1024 pixel 16M colors 85Hz refresh rate, incorporates PanelLink Digital
technology (Silicon Image)
-
Option: D-SUB (female HD15) connector available,
replaces DVI-I connector
|
|
USB
|
Ports over-current protected, data transfer rate of up to 12Mbps, conforming to USB1.1
- USB port 1: Type A connector (front panel)
- USB port 2: J2/P2 Rear I/O option
|
|
Ethernet
|
10/100Mbps Fast Ethernet controller, 82551ER chip, RJ45
|
Serial Port
COM1
|
-
On-board RS-232E transceiver, RJ45 front panel connector
(adapter RJ45 to D-Sub available), transceiver can be disabled if
rear I/O COM port option is preferred
- J2/P2 Rear I/O option (TTL voltage level)
|
|
Legacy I/O
|
-
LPC Super-I/O interface connector, CC6-ACID mezzanine companion board available
for top (right) or bottom (left) mounting
- J2/P2 Rear I/O option: Keyboard, Mouse, COM1 (TTL voltage level)
|
|
IDE/ATA
|
- Ultra ATA/100 40-pin connector (primary IDE)
- CompactFlash socket for CFA ATA cards (secondary IDE)
- J2/P2 Rear I/O option: Primary IDE
|
|
CompactPCI
|
32-bit, 33.3MHz, PCI bridge chip PLX 6150, 133MBps CPCI master
|
J2/P2
Rear I/O
Option
|
- Primary IDE
- USB Port 2
- Keyboard, Mouse
- COM1 (TTL Level)
- Rear I/O transition module CCY-RIO available
|
|
PXI Support
|
TRIG0, TRIG1, TRIG6, TRIG7 (can be alternatively used as GPIO)
|
|
BIOS
|
- Phoenix BIOS with EKF embedded systems enhancements
- 8Mbit Flash memory
- Updates available from website ekf.com
|
Drivers
(Major OS)
|
- Intel graphics drivers
- Intel networking drivers
|
Power
Requirements
|
- CC3-1-CAJUN: +5V±0.25V 1.3A max.+3.3V±0.1V 1.1A max.
- CC3-2-CAJUN: +5V±0.25V 1.9A max.+3.3V±0.1V 1.3A max.
|
Thermal
Conditions
Environmental
Conditions
|
Processor cooled down by passive heatsink, typical thermal resistance 13.8K/W
(natural convection), 4.6K/W (forced airflow @ 200LFM).
Custom specific heatsink solutions on request.
Maximum ambient operating temperature with standard heatsink:
- CC3-1: 0-40°C (natural convection cooling), 0-70°C1 (200LFM forced airflow)
- CC3-2: 0-60°C (200LFM forced airflow), 0-70°C1 (400LFM forced airflow)
- CC3-3: 0-45°C (200LFM forced airflow), 0-65°C (400LFM forced airflow), 0-70°C1 (600LFM forced airflow)
- CC3-4 0-40°C (200LFM forced airflow), 0-65°C (400LFM forced airflow), 0-70°C1 (600LFM forced airflow)
1 Limited to 70°C due to other components than the processor
- Storage temperature -40°C to +85°C, max. gradient 5°C/min
- Humidity 5% ... 95% RH non condensing
- Altitude -300m ... +3000m
- Shock 15g 0.33ms, 6g 6ms
- Vibration 1g 5-2000Hz
|
|
EC Regulations
|
- EN55022, EN55024, EN60950-1 (UL60950-1/IEC60950-1)
- 2002/95/EC (RoHS)
|
|
MTBF
|
0.113 * 106h
|
Typical Performance Rating
Measured with PCMark2002 under Windows 200
|
Board
|
Processor
|
CPU/MEM Score
|
|
CC3-1-CAJUN
|
400MHz ULV Celeron®
|
1274/886
|
|
CC3-2-CAJUN
|
650MHz ULV Celeron®
|
1990/933
|
|
CC3-3-CAJUN
|
800MHz LV Pentium®
|
tbd
|
|
CC3-4-CAJUN
|
933MHz LV Pentium®
|
2854/1467
|
Subject to change
CC3-CAJUN - Component Assembly (Top View)
|
CC3-CAJUN - Block Diagram
|
Available as a companion board to the CC3-CAJUN, the
CC6-ACID is provided with several
legacy I/O ports. This module can be mounted either to the bottom side or on
top of the CC3-CAJUN and communicates across the LPC (Low Pin Count) interface.
The CC6-ACID could be useful if the classical interfaces, e.g. serial and
parallel ports, are required by a given application.
|
|
In addition, the CC6-ACID can be delivered with an on-board 2.5-inch Ultra ATA
hard disk drive, resulting in a very compact system. Both COM connectors, LPT,
and PS/2 mouse and keyboard are situated at the CC6-ACID front panel
(4HP and 8HP versions available).
The CC0-CHILLOUT is similar to the CC6-ACID,
but designated for use together
with a rear I/O transition module (CCZ-RIO).
|
Available as a stuffing option, the CC3-CAJUN can be delivered for rear I/O
utilization. Several I/O ports can be routed across the J2 connector.
Rear I/O requires that a suitable J2 backplane is present in your CompactPCI
system. By default, the CC3-CAJUN is equipped with line terminating resistors
for a common 64-bit CPCI J2 backplane.
|
|
The CCY-RIO transition module provides a 4HP back panel with connectors for PS/2
style keyboard and mouse, a serial RS-232E COM port, and an USB receptacle.
In addition, optional on-board headers are provided on the CCY-RIO for internal
attachment of IDE/ATA devices (hard disks, optical drives).
|
CCY-RIO - Assembly Drawing
|
|
Ordering Information
|
|
Alias
|
Ordering No.
|
Short Description
|
|
CAJUN
|
CC3-1-CAJUN
|
3U/4HP CPCI CPU Board, ULV Celeron 400MHz µFCBGA 0.13µ processor,
256MB SDRAM, 256KB cache, 100MHz FSB
|
|
CAJUN
|
CC3-2-CAJUN
|
3U/4HP CPCI CPU Board, ULV Celeron 650MHz µFCBGA 0.13µ processor,
256MB SDRAM, 256KB cache, 100MHz FSB
|
|
CAJUN
|
CC3-3-CAJUN
|
3U/4HP CPCI CPU Board, LV Pentium III 800MHz µFCBGA 0.13µ processor,
256MB SDRAM, 512kB cache, 133MHz FSB
|
|
CAJUN
|
CC3-4-CAJUN
|
3U/4HP CPCI CPU Board, Pentium III 933MHz µFCBGA 0.13µ processor,
256MB SDRAM, 512kB cache, 133MHz FSB
|
|
|
CC3-8-CAJUN
|
512MB SDRAM Option
|
|
ACID
|
CC6-1-ACID
|
3U Super-I/O module, local mezzanine expansion board complementing optionally
the CC3-CAJUN, front panel 8HP, intended for front panel I/O,
mounting on top of the CC3-CAJUN
|
|
ACID
|
CC6-3-ACID
|
Similar to the CC6-1-ACID, front panel width 4HP, w/o parallel port,
mouse/keyboard combined in one Mini-DIN connector (external splitter
cable available as accessory), mounting on the top or to the
bottom side of the CC3-CAJUN
|
|
ACID
|
CC6-8-HDK
|
Optional hard disk drive, on-board mounting on top of the CC6-1 and CC6-3
|
|
RIO
|
CCY-1-RIO
|
Rear I/O transition module for CC3-CAJUN
|
|
ADAPT
|
CR9-5-ADAPT
|
Mechanical kit, expands the CC3 front panel to 6U full height
|
|
|
261.92.009.01
|
Adapter for front panel RS-232 usage, RJ45 jack to male D-Sub connector 9-pos.,
customer configurable, suitable e.g. for COM-port emulation
|
|
|
261.91.009.01
|
Adapter for front panel RS-232 usage, RJ45 jack to female D-Sub connector 9-pos.,
customer configurable, suitable e.g. for null-modem emulation
|
|
|
280.7.400
|
external keyboard/mouse Y-splitter-cable Mini-DIN male to 2 x Mini-DIN female
(required for CC6-3 only)
|
|
|
908.51.02.01
|
DVI-D to DVI-D cable assembly, 2m, connects the CC3-CAJUN to DVI monitors
(digital way)
|
|
|
908.57.02.01
|
DVI-I to HD DSUB15 cable assembly, 2m, connects the CC3-CAJUN to VGA monitors
(analog way)
|
|
|
908.57.12.01
|
DVI-I to VGA adapter (plug to receptacle), to be plugged onto the CC3-CAJUN DVI
output, with HD DSUB15 socket, suitable especially for analog monitors with
attached VGA cable
|
|
