CC6-ACID & CC0-CHILLOUT
CompactPCI Super-I/O Module
Optional Hard Disk Drive on-Board
Available as a companion board to several EKF CompactPCI CPU cards, the CC6-ACID
(CC0-CHILLOUT) is provided with the legacy I/O ports of a classic PC, e.g.
serial and parallel interfaces. Interconnection between the CC6 (CC0) I/O module
and the host CPU board is achieved by the LPC (Low Pin Count) interface. As an
option, the CC6-ACID (CC0-CHILLOUT) is available with a rugged on-board 2.5-inch
hard disk drive.
|
|
The connectors COM1/2, LPT, mouse and keyboard are situated on the CC6-ACID
front panel, whereas the CC0-CHILLOUT has been designed solely for rear I/O.
In addition, both boards are provided with several on-board connectors, e.g.
for attachment of a floppy disk drive. The Super-I/O companion boards can be
attached either to the left or to the right of the CPU card (top or bottom
mounting).
|
|
CC6-1-ACID - 3U Super-I/O Module
|
The CC6-ACID (CC0-CHILLOUT) communicates with the host CPU by means of the
LPC interface. This is a multiplexed ISA bus, enabling the Super-I/O controller
chip to emulate the legacy I/O interfaces. Among these are parallel and serial
ports, the PS/2 connectors, and last not least the classic 1.4/2.8MB floppy
disk controller. As an option, the CC6-ACID (CC0-CHILLOUT) provides MIDI and
joystick attachment, and control lines for fans with either tachometer output
or pulse width modulation input.
By connecting the boards together, the hosts ATA/IDE interface is also available
on the CC6-ACID (CC0-CHILLOUT). Optionally, the board is equipped with a robust
2.5-inch hard disk drive, particularly suited for use in a rugged environment.
The CC6-ACID can be mounted either on the left (bottom) side of the CPU board
(version CC6-3 only), or right (top) side (both CC6-1 and CC6-3). The way of
attachment (top or bottom with respect to the CPU) can be easily changed by
oneself (this is not true for the CC0-CHILLOUT). Suitable CompactPCI host-CPU
boards are the CC2-TANGO, CC5-RAVE, CC7-JAZZ and CC8-BLUES.
|
|
Regarding the CC6-1-ACID, the connectors COM1, COM2, LPT, PS/2 keyboard and
mouse can be reached from the boards front panel (width 8HP). The CC6-3-ACID
comes with a 4HP front panel (LPT connector removed). When using the CC6-3,
mouse and keyboard are sharing the same Mini-Din connector by means of an
external splitter cable.
The CC0-CHILLOUT does not provide any connector on its front panel, which is
shared with the CPU board and 8HP wide in total. Instead, all signals are wired
to the connectors J1/J2. By means of an additional rear I/O transition module (CCZ-RIO),
the I/O connectors are available from the back panel. The CC0 comes ready
assembled with the CPU board only.
Additional I/O functions are provided by on-board pin-headers on the CC6-ACID
(CC0-CHILLOUT).
The Super-I/O companion boards must be inserted beside the CompactPCI bus.
No backplane is required for the CC6-ACID. The CC0-CHILLOUT however needs a
single-slot rear I/O backplane (P1/P2) to be present.
|
Typical Alignment of CC6/CC0 with Respect to the CPCI Backplane
|
|
Feature Summary CC6-ACID and CC0-CHILLOUT
|
|
Form Factor
|
Single size Eurocard (160x100mm2)
- Front panel width CC6-1: 8HP (40.6mm)
- Front panel width CC6-3: 4HP (20.3mm)
- Joint front panel width CC0 & CPU board: 8HP (40.6mm)
|
|
LPC Super-I/O Chip
|
LPC47B27x, parallel port, 2 serial ports, floppy drive controller port,
keyboard controller & mouse port, infrared port, MIDI/gameport, fan control
ports, GPIOs, serial IRQs
|
Front Panel
Connectors 4
|
-
CC6-1: keyboard PS/2, mouse PS/2, COM1 COM2 (RS-232E 9-pos. D-Sub male), LPT
(25-pos. D-Sub female)
-
CC6-3: keyboard PS/2, mouse PS/2 available with external splitter-cable
(accessory), COM1 COM2 (RS-232E 9-pin D-Sub male)
|
|
On-Board Connectors 1
|
LPC interface, IDE/ATA 40-pin header 2.54mm, IDE/ATA 44-pin header 2.00mm,
floppy disk header 34-pin 2.54mm
Optional: FFC/FPC floppy disk 26-pos. ZIF receptacle 2,
floppy disk power, 2 x fan header (pulse width modulation), 2 x fan header
(tacho generator), MIDI/gameport header
|
J1/J2
CPCI respectively
Rear I/O
Connectors
|
-
CC6-ACID: J1, allows for redundancy in power attachment 3.3V 5V 12V, in addition
to LPC connector
-
CC0-CHILLOUT: J1/J2, utilization as rear I/O handover connectors to a single
slot backplane P1/P2, in addition a suitable rear I/O transition module is required
|
|
Rear I/O Interfaces 2
|
-
J1: IDE, PS/2 keyboard, PS/2 mouse, joystick, Ethernet 3, video 3 analog / digital
-
J2: Floppy disk, LPT, COM1/2 (TTL and optional RS-232E), utilities, USB 3
|
|
On-Board Functions 1
|
Speaker, LED IDE activity, optional LEDs: GPIO21, GPIO22, GPIO43, GPIO60, GPIO61,
3.3V, 5V, 12V
|
|
Hard Disk Option
|
HDD 2.5-inch optional on-board, Ultra ATA/100
|
|
MTBF
|
0.185 * 106h
|
1 Some of the on-board connectors and on-board functions are available as an option only
2 Functions/features available only with CC0-CHILLOUT
3 These options require removing of the particular host CPU front panel
connectors
4 Functions/features available only with CC6-ACID
subject to technical changes
CC6-ACID - Block Diagram
|
CC0-CHILLOUT - Block Diagram
|
CCZ-RIO - Block Diagram
|
CC6-ACID - Component Assembly
|
CC0-CHILLOUT - Component Assembly
|
|
Ordering Information
|
|
Alias
|
Ordering No.
|
Short Description
|
|
ACID
|
CC6-1-ACID
|
3U Super-I/O module, expansion board to the CC2-TANGO, CC5-RAVE, CC7-JAZZ and
CC8-BLUES, front panel width 8HP, to be mounted on top of the CPU
(to the right of the CPU)
|
|
ACID
|
CC6-3-ACID
|
Similar to CC6-1-ACID, front panel width 4HP, without parallel port connector,
keyboard/mouse combined in one Mini-DIN connector (external splitter cable
available as accessory), to be mounted on the top or bottom of the CPU
(to the right or left of the CPU)
|
|
|
CC6-8-HDK
|
Option hard disk, available together with CC6-1-ACID and CC6-3-ACID, completely mounted
|
|
|
280.7.400
|
External keyboard/mouse Y-splitter-cable Mini-DIN male to 2 x Mini-DIN female
(required for CC6-3 only)
|
|
CHILLOUT
|
CC0-1-CHILLOUT
|
3U Super I/O module for rear I/O systems, various assembly options and on-board
hard disk possible, available only as ready assembled unit together with host
CPU board, shared front panel 8HP in total
|
|
RIO
|
CCZ-1-RIO
|
Rear I/O transition module for CC0-CHILLOUT
|
|
|
932.2.01.000
|
P1/P2 Single Slot Rear I/O Backplane
|
CC6-3-ACID 4TE Super-I/O Modul |
|
